KB
STABILIZER - Developed by Kurt Beauregard. Field tested. Fits #110 - #330 and everything in between.
| ~~ STABILIZER STAKES & TRAP SUPPORTS ~~ | |
|
H-TYPE / DOUBLE BAR |
||
| ˝ Dozen | Dozen | |
| for #110 / 120 - 12" Tall | $12.95 | $23.95 |
| for #110 / 120 - 24" Tall | $14.95 | $26.95 |
| for #160 - 13" Tall | $13.75 | $24.45 |
| for #220 - 13" Tall | $13.95 | $24.95 |
| for #280 - 20” Tall | $19.95 | $36.95 |
| for #280 - 46” Tall | $34.95 | $62.95 |
| for #330 - 20" Tall | $19.95 | $37.95 |
| for #330 - 46" Tall | $35.95 | $64.95 |
|
STAKEALIZER
|
|||
| Each | ˝ Dozen | Dozen | |
| STAKEALIZER ON 18” STAKE | $2.95 | $15.95 | $29.95 |
|
SCREW-IN STAKEALIZER (can use on trees, log crossings, etc.) |
$2.25 | $11.95 | $22.95 |
KB
STABILIZER - Developed by Kurt Beauregard.
Field tested. Fits #110 - #330 and everything in between.
Works for: snow sets, otter crossovers, bridge abutments,
culverts, bottom edge sets, coon trails, soft peat or muck bottoms, and nuisance
work.
You’ll Need No Other!
| Each | ˝ Dozen | Dozen |
| $3.25 | $16.95 | $32.95 |
Patent Pending
BERKSHIRE STABILIZER STAKE
for 110 TRAPS
Permanently attached to trap for easy handling. Prevents the animal from
knocking the trap over. Speeds your setting time. Easier to conceal than other
staking methods. Perfect for setting those hard-to-reach deep channels and dens.
$12.95 dozen
POCKET POPPERS
by Jim Blakley
The
Pocket Popper is an injection molded plastic body gripper stabilizer that can be
stuffed into the mouth of a pocket and hold a 110/120 size trap ready to catch.
This square black box may look goofy, but animals have no fear of it. Used to
successfully take over 1000 mink. When it is impossible to get a standard pocket
dug, cut sod or pile creek side debris to put over the popper. Also use in rock
cubbies, side of muskrat houses, and in drain tiles. If it is starting to freeze
up or is already frozen, place the popper just above the water level. It will
keep working even below zero. Use successfully for marten by placing it at the
mouth of climbing pole cubbies.
$3.95 each
$39.95 dozen
| ˝ Dozen | Dozen | |
| #220 ... | $14.95 | $24.95 |
| #160 ... | $14.90 | $24.90 |
BARKERS CONI-MOUNT
Metal bracket used to hold body gripper type
traps. Made of steel and has three holes located down the center
to permit fast, easy fastening. Nail it to a limb, log, tree,
board or stake where you want to locate the trap. Set the trap
in the normal manner, except let the jaws close onto the Coni-Mount.
Trap is held solidly in position until it is sprung. It cannot
tip, twist, slide sideways, fall over or be knocked over.
| Coni-Mount I | - for sizes 100, 110, 120 | - $11.95 dozen |
| Coni-Mount II | - for sizes 150, 160, 200, 210, 220, 250, 280 | - $12.95 dozen |
| Coni-Mount III | - for sizes 300, 330 | - $16.95 dozen |
TRAILLEG STABILIZERS
by RSP Stabilizers
Trailleg Stabilizers were developed primarily for trappers who
like to set bodygrip traps in blind trails for coon and mink. The Trailleg
Stabilizers bolt right on to your trap in place of the existing rivets. With the
stabilizers directly attached to the trap, there is no need to carry any extra
equipment. Trailleg Stabilizers will help you to simplify and speed up your
approach to trail setting.
We carry as an in-stock item modified Duke #110 Magnum and #220 bodygrip traps
with the Trailleg Stabilizers already installed.
| DUKE TRAIL TRAP: Trailleg Installed |
 |
|||
| Each | ˝ Doz | Dozen | ||
| Duke #110 Magnum | $6.20 | $34.95 | $61.95 | |
| Duke #220 | $11.70 | $65.95 | $116.95 | |
| TRAILLEG STABILIZERS: You Install - Instructions Included | ||||
| Each | ˝ Doz | Dozen | ||
| #110 - Fits Most Brands | $2.20 | $13.00 | $22.00 | |
| #220 - Fits Most Brands | $2.40 | $16.00 | $24.00 | |
BAIT TRIGGER
Simply attach to jaw of any model body gripper trap, screw
poplar bait stick onto trigger and set. The trap sets off when the animal
attempts to take the bait stick. Make a bait set anywhere. A real producer for
the under-ice beaver trapper. Very simple and extremely effective.
$2.95 each
$30.00 dozen